SPI Protocol Analysis for Ics
SPI (Synchronous Peripheral Interface) is a 4-wire Protocol Analyzer which communicates by Master-Slave mode. It consists of SCK、MOSI (SDO)、MISO (SDI) and SS (CS). SPI is mostly applied in LCD control, SD / MMC, Flash / EEPROM, etc. In a word, it is used very commonly.
Besides the above 4 pins, SPI also has another two important parameters, they are CPHA and CPOL, which can produce 4 kinds of different SPI Mode, and the 4 kinds of different SPI Mode can decide the mode of data coding in SPI signal. With Zeroplus logic analyzers and SPI protocol analysis capability, engineers can capture, decode, and interpret SPI signals more efficiently for microcontroller, Flash, EEPROM, and embedded system communication debugging.
SPI Analysis Function Introduction
When the SPI Protocol Analyzer auto-coding function is turned on, MOSI / MISO Protocol Analyzer and its signal data will display on the screen. Furthermore, through SPI custom setting, it not only can define the used I/O pin but also can choose whether display the MOSI (SDO) / MISO (SOI) and activate SS (CS).In SPI custom setting, when the SS (CS) is activated, SS enable level can be selected High / Low, and the data length can be set in data setting part, the data length range is 1 ~ 28bit.
- BUS Line: SS、MOSI、MISO、SCLK
- Frequency: 10M ~ 150MHZ
- Voltage: Depend to Datasheet
- Area of Project Application: EEPROM
- Gallery
- Download
-
40 Channels High Speed Logic Analyzer
LAP-F140512M | FM00006147
The 40-channel High-Speed Logic Analyzer: Engineered for synchronized multi-bus measurement...
Details64-Channel Synchronous Logic Analyzer
LAP-F164064 | FM00002619
Harnessing a 64-channel synchronous monitoring core, this system supports internal timing sampling...
Details64-Channel Advanced Logic Analyzer
LAP-F164256M | FM00006156
The 64-Channel Advanced Logic Analyzer stands as a perfectly balanced model, integrating 64-channel...
Details16-Channel Entry-Level High-Performance Logic Analyzer
LAP-C Pro 16064M | FM00007890
The 16-Channel High-Performance Logic Analyzer is ideal for digital development tasks requiring...
Details32-Channel High-Performance Logic Analyzer
LAP-C Pro 32064M | FM00007893
The 32-Channel High-Performance Logic Analyzer is ideal for digital system verification tasks...
Details32-Channel Advanced High-Performance Logic Analyzer
LAP-C Pro 32128M | FM00007896
The 32-Channel Advanced High-Performance Logic Analyzer is ideal for development and verification...
Details32-Channel Flagship High-Performance Logic Analyzer
LAP-C Pro 32256M | FM00007899
The 32-Channel Flagship High-Performance Logic Analyzer is ideal for advanced development environments...
Details16-Channel Standard Logic Analyzer
LAP-C 16064 | FM00000118
The 16-channel standard logic analyzer is ideal for daily debugging needs such as microcontroller...
Details16-Channel Enhanced Logic Analyzer
LAP-C 16128 | FM00000116
The 16-channel enhanced logic analyzer is designed for embedded development, digital debugging,...
DetailsProCision System Stability Analyzer
FM00011874
The ProCision is a high-density system stability analyzer engineered to replace limited 4-channel...
DetailsSetting Up the SPI Decoder Correctly
SPI uses SCLK, MOSI, MISO and a slave select (SS), and CPOL and CPHA define four SPI modes. A decoder set to the wrong mode reads shifted or inverted data, which is one of the most common reasons SPI captures look wrong even when the bus is working.
The Zeroplus SPI decoder configuration lets you assign each pin, choose the SS enable level (high or low) and set a data length from 1 to 28 bits before it displays MOSI and MISO data. In ZP-Logic, MISO and MOSI can be grouped into one bus, and SPI is a hardware trigger protocol on LAP-F1 models. For selection, compare the SPI clock rate with the analyzer's sample rate.










